The Fusion ranks among the better family sedans of its time. The 2010 update is extensive and rectifies the road noise and turning circle shortcomings of the original car. The V6 engine is still responsive and gets good fuel economy. Ride and handling remain competent and stability control is now standard. Interior fit and finish has improved. Rear-seat room is acceptable but falls a bit short compared with the competition.
Alerts
There are 6 recalls on this vehicle. Learn More.

Reliability

Reliability indicates how models have performed in the past, providing the basis for predicting how the vehicles will hold up in the year ahead. These charts provide the most comprehensive reliability information available to consumers. Based on information received from our latest subscriber survey, our reliability history charts give you a rundown on how used vehicles are holding up in 17 potential trouble spots, ranging from the engine, transmission, and brakes to power equipment and the electrical system.

Overall Reliability
Most Common Trouble Spots
Common Trouble Spot
Common Trouble Spot
The 2012 Ford Fusion has been recalled 6 times by NHTSA. View Recalls
Research Years * Redesign year
Worse Better
00
01
02
03
04
05
06*
07
08
09
10*
11
12
13*
14
15
16
17
18
19
20
Overall Reliability Verdict
NA
POTENTIAL TROUBLE SPOTS
Engine Major
NA
Engine Minor
NA
Engine Cooling
NA
Transmission Major
NA
Transmission Minor
NA
Drive System
NA
Fuel System
NA
Electric System
NA
Climate System
NA
Suspension
NA
Brakes
NA
Exhaust
NA
Paint/Trim
NA
Body Integrity
NA
Body Hardware
NA
Power Equipment
NA
In-car Electronics
NA
Reliability indicates how models have performed in the past, providing the basis for predicting how the vehicles will hold up in the year ahead. These charts provide the most comprehensive reliability information available to consumers. Based on information received from our latest subscriber survey for about 329,000 vehicles, our reliability history charts give you a rundown on how 2000 through 2020 vehicles are holding up in 17 potential trouble spots, ranging from the engine, transmission, and brakes to power equipment and the electrical system. NA indicates that we did not receive a large enough sample size to provide data for a specific year. An X indicates that the vehicle was not manufactured for a specific year.

Learn more about car Reliability.

Owner Reported Trouble Spots

The Reliability score is based on our latest subscriber survey of 2012 Ford Fusion owners. The owner comments describe problems respondents experienced with this vehicle.

Brakes

Antilock system (ABS), parking brake, master cylinder, calipers, rotors, pulsation or vibration, squeaking, brake failure or wear.

What Owners Say

Antilock system (ABS)

"The dealer fix the problem"

Anonymous, (2012 Ford Fusion SEL 3.0-L V6)

"During cold weather of -3 deg F, all power assisted brake features failed. It took three trips to the dealer ship to get repaired . I wrote three incident reports to NHTSA"

Anonymous, MI (2012 Ford Fusion Hybrid 2.5-L 4 Cyl hybrid)
Calipers

"Stuck rear calipers needed replacement"

Jeffrey K., IL (2012 Ford Fusion S 2.5-L 4 Cyl)

"Corrosion prevented complete retraction of rear piston causing pad and rotor wear."

Anonymous, NH (2012 Ford Fusion SEL 2.5-L 4 Cyl)

"Caliper failed after 75000 miles. This seemed premature failure!"

D D., NY (2012 Ford Fusion SEL 3.0-L V6)

"I had to replace all of the calipers two years in a row. This is uncommon."

Donald G., IL (2012 Ford Fusion SE 2.5-L 4 Cyl)

"Rear caliper stuck closed causing premature break wear on rear brakes."

J B., NY (2012 Ford Fusion Sport 3.5-L V6)

"The technicians had a problem identifying the issue until it became very noisy and the wheel was hot to the touch. The mechanic identified it immediately, told me it was too dangerous to drive. It was then repaired within a day."

Anonymous, OH (2012 Ford Fusion SE 2.5-L 4 Cyl)

"they were worn out and the repair shop initially did the repair incorrectly"

Timothy M., NY (2012 Ford Fusion SEL 2.5-L 4 Cyl)

"The rear driver's side caliper started sticking inexplicably, but I was able to free it, and it has not been an issue since."

Anonymous, MD (2012 Ford Fusion SEL 2.5-L 4 Cyl)

"Rear caliper seized, replaced both, due to high mileage."

Anonymous, ON (2012 Ford Fusion SE 2.5-L 4 Cyl)

"Rear driver side caliper seems to seize, and create excessive heat and smell. This is even after recent brake service. Discontinued use of the parking brake, to see if that helped."

Anonymous, ON (2012 Ford Fusion SEL 2.5-L 4 Cyl)

"Calipers seized. The vehichle had bee checked within 500 km and no concern was identified"

Anonymous, ON (2012 Ford Fusion SEL 2.5-L 4 Cyl)

"calipers failed (sticking), resulting in noise and total wear of the break pads and rotors"

Anonymous, BC (2012 Ford Fusion SEL 3.0-L V6)
Master cylinder

"Brakes were not working correctly. Replaced at a cost of parts and labor of just over $3000"

Alec M., FL (2012 Ford Fusion SE 2.5-L 4 Cyl)

"Breaks were squishy and car hard to stop"

Anonymous, NY (2012 Ford Fusion SEL 2.5-L 4 Cyl)
Normal routine brake wear

"Car had enough miles that rear brakes needed replacing. Fronts had been replaced before I bought it."

Anonymous, MN (2012 Ford Fusion SE 2.5-L 4 Cyl)

"Normal brake wear as previously detected on oil change."

Anonymous, IL (2012 Ford Fusion SEL 2.5-L 4 Cyl)

"Rear Brake pads needed to be replace due to normal wear."

Anonymous, WA (2012 Ford Fusion SE 2.5-L 4 Cyl)

"I took my car to be detailed, and was told I needed new rear brake pads. They did the job, and that's all I know."

Anonymous, (2012 Ford Fusion Unsure Unsure)

"I viewed my pads getting low and decided to replace pads before noise starts."

Anonymous, AZ (2012 Ford Fusion SE 2.5-L 4 Cyl)

"Brake noise indicated the problem; resolved with normal brake work."

Anonymous, MI (2012 Ford Fusion SE 2.5-L 4 Cyl)

"This issue began in late June 2020. We purchased the parts (new brake pads) and had them installed"

Anonymous, (2012 Ford Fusion SE 2.5-L 4 Cyl)

"Had to replace the brakes because of normal wear and tear."

Anonymous, FL (2012 Ford Fusion SE Unsure)

"Front and rear brakes replaced at 85000"

Anonymous, FL (2012 Ford Fusion Sport 3.5-L V6)

"Wasn't braking well. Had it checked and it needed new pads and rotors"

Anonymous, NE (2012 Ford Fusion Unsure 2.5-L 4 Cyl)

"just normal wear and tear needed replacement"

Anonymous, WI (2012 Ford Fusion)
Parking brake

"When the outside temperature is below freezing, the parking brake on the right rear wheel becomes frozen and does not release when the parking brake lever is disengaged. I can’t put the vehicle in motion easily from a cold start. After a few minutes to warm up, the brake frees up, allowing the wheel to turn. The dealer solution was to replace the parking brake drums on each wheel. They did not replace the cables leading from the parking brake lever to the wheels, which I think is the problem. My current workaround is to not engage the parking brake when the weather forecast is freezing temperatures for the next morning."

Frank Y., MO (2012 Ford Fusion SEL 2.5-L 4 Cyl)

"Just like the steering box freezing in fridge weather, water in the steering box, the parking brake freezes in sub freezing weather."

Robert F., PA (2012 Ford Fusion SE 2.5-L 4 Cyl)

"Caliper for parking brake froze open and parking brake cable broke."

Anonymous, NY (2012 Ford Fusion SEL 2.5-L 4 Cyl)
Premature brake wear

"Replaced rear pads and rotors at 60000 km., consider ths premature as I drive attempting to use brakes to a minimum"

David G., ON (2012 Ford Fusion SE 2.5-L 4 Cyl)

"Rear brake pads completely wore out"

D D., NY (2012 Ford Fusion SEL 3.0-L V6)

"See previous comments"

Anonymous, CA (2012 Ford Fusion SE 2.5-L 4 Cyl)

"Had a bad brake caliper right rear"

Alan L., NH (2012 Ford Fusion SE 2.5-L 4 Cyl)

"brakes sent seem to last"

Anonymous, ON (2012 Ford Fusion SE 2.5-L 4 Cyl)

"Sudden rotor failure on front drivers side and some damage to caliper. Passenger side was replaced as a safety measure."

Anonymous, VA (2012 Ford Fusion SE 3.0-L V6)

"The brakes actually failed; the left rear brake engaged after I used the parking brake and would not release. It happened multiple times. Thankfully I was able to get it to release and drive after a time, but it was actually dragging the back tire. The service stated water had gotten into the brake system in the back causing it to fail and lock on. They had to replace the whole brake assembly on both sides."

Valerie P., ID (2012 Ford Fusion SE 3.0-L V6)

"noisy rear brakes (recently rebuilt)"

Bruce C., ON (2012 Ford Fusion SEL 2.5-L 4 Cyl)

"See caliper problem."

Anonymous, NH (2012 Ford Fusion SEL 2.5-L 4 Cyl)

"significant noise from rear brakes and wear issues required replacement of most components, however front brakes were fine with only moderate wear."

Anonymous, MI (2012 Ford Fusion SE 2.5-L 4 Cyl)

"According to my mechanic stuck calipers are a common problem on Ford Fusions. You would think they would know how to make brakes by now."

J B., NY (2012 Ford Fusion Sport 3.5-L V6)

"Had to replace breaks"

Angel O., MA (2012 Ford Fusion S 2.5-L 4 Cyl)

"Rear brakes are almost worn out with less than 35,000 miles"

Anonymous, MD (2012 Ford Fusion SE 3.0-L V6)

"Rear brakes needed replacement at 26, 000 miles. Thought that was unusual. Front pads were still fine. Was told Ford made the rear pads half as thick as the front pads"

Tom S., NC (2012 Ford Fusion SEL 2.5-L 4 Cyl)
Pulsation or vibration

"The front rotors and pads were replaced due to normal wear."

Anonymous, VA (2012 Ford Fusion SE 3.0-L V6)
Regular brake failure

"There was warning of potential brake failure. Was caught during normal maint. cycle"

Robert K., ON (2012 Ford Fusion SEL 2.5-L 4 Cyl)
Rotors

"Just normal wear needed to be replaced."

Anonymous, MN (2012 Ford Fusion SE 2.5-L 4 Cyl)

"As mentioned is the last description, I have a rotor suddenly fail which prevented driving the vehicle."

Anonymous, VA (2012 Ford Fusion SE 3.0-L V6)

"rusted, needed to be replaced"

Jonathan L., NY (2012 Ford Fusion SE 2.5-L 4 Cyl)

"Rotors rusted and required resurface even thought car is garage kept as storage 3 months of the year"

Barry C., NJ (2012 Ford Fusion SEL 2.5-L 4 Cyl)

"Rotors were corroded"

Anonymous, NJ (2012 Ford Fusion SE 2.5-L 4 Cyl)

"Rusting"

Anonymous, ME (2012 Ford Fusion SE 3.0-L V6)

"We had to replace break rotors because they were warped. This car was in a front-end accident"

Henry D., NE (2012 Ford Fusion SE 2.5-L 4 Cyl)

"just replaced rotors and pads"

Anonymous, PA (2012 Ford Fusion SE 2.5-L 4 Cyl)

"vibrates when brakes are applied"

Duane S., IA (2012 Ford Fusion SEL 3.5-L V6)
Squeaking

"It has a what I would call a winning noise that sounds like a power steering pump or belt but when checked no one seems to be able to figure out what it is or where it is coming from"

Ronald W., MA (2012 Ford Fusion SE 2.5-L 4 Cyl)

"The squeaking was related to the brakes locking. Prior to complete locking they were squeaking and making noises. I thought since it was snowy and muddy it was simply dirty, but the brakes were about to completely fail; it was really a warning."

Valerie P., ID (2012 Ford Fusion SE 3.0-L V6)

"More of a shuddering. Especially when braking from highway speeds. Have not been able to determine the cause"

David J., NC (2012 Ford Fusion SEL 3.0-L V6)

"When you press hard on brakes it makes a pedal noise"

Joseph D., ON (2012 Ford Fusion SE 2.5-L 4 Cyl)

Climate System

Blower (fan) motor, A/C compressor, condenser, evaporator, heater system, automatic climate control, refrigerant leakage, electrical failure.

What Owners Say

A/C compressor

"It stopped working"

Marilyn G., FL (2012 Ford Fusion)

"compressor started making whining problems. Took it in to the dealer and had compressor replaced. Next day the compressor made noise again. They replaced the compressor again. Then again the next day it also failed to produce cool air. Thjey replaced compressor again and then found that the evaporator had considerable moisture in it,so the evaporator was replaced along with the compressor and since then it has worked normally"

Jack H., NE (2012 Ford Fusion SE 3.0-L V6)

"the A/C stop working"

Angel O., MA (2012 Ford Fusion S 2.5-L 4 Cyl)

"AC stopped working"

Angel O., MA (2012 Ford Fusion S 2.5-L 4 Cyl)

"2012 Blend Door Air-conditioning problem."

Anonymous, MO (2012 Ford Fusion SE 3.0-L V6)

"The air stopped being cold last summer. I don't get it fixed because the defroster still worked and I didn't feel it was an urgent issue. This summer, the defroster stopped working. The compress was leaking oil. So I has it replaced. It works fine now."

Anonymous, (2012 Ford Fusion Sport 3.5-L V6)

"There was a problem with a valve and fitting, not very efficient cooling. Expensive to repair because of the labor involved, part was only 275 but labor was many hundreds"

Anonymous, (2012 Ford Fusion SE 2.5-L 4 Cyl)

"It stopped cooling my car. I took it to a dealer and he replaced something and it solved the problem. Cost was high but in Florida you need air conditioning"

Anonymous, MA (2012 Ford Fusion Unsure Unsure)

"A/C would be working fine, but then start blowing hot air. It was a known problem by Ford, and it took four months to finally get the part needed to repair the problem. It was an intermittent problem which unfortunately occured during the summer"

Hal S., FL (2012 Ford Fusion SE 2.5-L 4 Cyl)

"Cold air would cut out"

Anonymous, ON (2012 Ford Fusion SE 2.5-L 4 Cyl)
Automatic climate control

"A/C blowing hot air"

C G., AZ (2012 Ford Fusion SE 2.5-L 4 Cyl)

"There is a part that has a history of feeling in the Ford fusion. It makes the heater go full blast and negates the use of the air-conditioner. If you use the air conditioner only the hottest of air will come out. This is about $1000 fix which has been going on long before your report on the 2012 fusion"

Anonymous, CA (2012 Ford Fusion SE 2.5-L 4 Cyl)

"The air conditioning quit working. A $30 part needed replacing. This required removing the entire dashboard. The air conditioning still didn't work and another part had to be replaced after removing the entire dashboard. $1700."

Anonymous, MN (2012 Ford Fusion S 2.5-L 4 Cyl)

"The 2012 Ford Fusion is among those models experiencing blend door problems."

Anonymous, MO (2012 Ford Fusion SE 3.0-L V6)

"Programming problem with onboard computer that Ford reprogrammed to fix issue at the tune of $250."

Anonymous, KS (2012 Ford Fusion SE 2.5-L 4 Cyl)

"A?C Unit was blowing HOT air when activated. Took 3 service visits before the dealer service shop got the repair right. First, faulty temp blend door control motor. Performed module actuator position calibration. Paid #231.47, Next day I was back at the dealership, same problem. They performed a check and decided it was something else. Paid more money, $200.00, negotiated price. Back again 2 days later. Dealership service dept then installed A/C control module. Wanted over $600.00 more!!! After discussions w/ tech and Service Dept manager, I grudgingly paid them another $200.00. Took vehicle home and it has not had any problems related to A/C system since."

Anonymous, NJ (2012 Ford Fusion SE 3.0-L V6)

"sensor failure causes AC to blow hot intermitantly without warning. Repair is expensive due to location (remove dash!). Local dealer unwilling to fix and stalled until 12K warranty expired. Bad feelings, will not buy another ford car (I like the tr"

Carl Y., GA (2012 Ford Fusion SE 2.5-L 4 Cyl)

"Hot air blowing out the dashboard vents when the system is not turned on"

Peter S., AZ (2012 Ford Fusion Hybrid 2.5-L 4 Cyl hybrid)

"A/C would switch to heat by itself"

Bruce N., MA (2012 Ford Fusion SE 2.5-L 4 Cyl)

"vent system has a gargling water sound combined with a clicking fan noise. Dealer was aware of it and provided a fix. Fix made the issue worse and needs to return to the dealer again"

Jason O., AB (2012 Ford Fusion SEL 2.5-L 4 Cyl)
Blower (fan) motor

"The blower fan motor makes a constant squeeling sound. I have purchased an OEM replacement and the replacement does the same exact thing. I guess there is no option to fix this very annoying issue"

Corbin L., CT (2012 Ford Fusion SEL 2.5-L 4 Cyl)

"Wiring and blower motor shorted out twice."

Anonymous, KY (2012 Ford Fusion SE 3.0-L V6)

"Fan motor replaced under warranty in January 2019, has recently started making bad noise June 2019."

Dean S., VA (2012 Ford Fusion SE 2.5-L 4 Cyl)

"Blower fan replaced under warranty. Failed again six months later."

Dean S., VA (2012 Ford Fusion SE 2.5-L 4 Cyl)

"The fan makes a noise as if the bearings are wearing out or something is rubbing against something else at most speeds. Also, the damper for hot/cold failed."

Anonymous, TX (2012 Ford Fusion SE 2.5-L 4 Cyl)

"AC fails to work, it blows hot. AC will work occasionally. The vents stick it seems. This seems to be a common problem according to youtube."

Anonymous, TX (2012 Ford Fusion SE 3.0-L V6)

"This occurs in spurts. Usually right after starting, the blower motor will cut out for 6-12 seconds, then come back on. This may also occur while driving, for about the same amount of time. OBD shows no errors with blower motor. Have already replaced HVAC thermal resistor switch once for a different issue (stuck on one fan speed regardless of setting) which did not resolve the issue. As it is very intermittent and for a short amount of time (I will have a week when it happens frequently, then not again for weeks), I have not been able to get it looked at by a mechanic when the issue is acting up. As mentioned, I replaced the fan's thermal resistor when the vehicle had less than 80,000 miles, which I think is a terrible indicator of the quality of components used. This is also a frequent issue with Fords of this era."

Anonymous, WA (2012 Ford Fusion SE 3.0-L V6)

"stopped intermitantly then replaced"

Anonymous, (2012 Ford Fusion SEL 3.0-L V6)

"I had the motor replaced once already, under warranty. At that time it make a horrible loud ticking noise and would only stop when I shut off the whole system. The replacement motor makes a low tick noise and will stop when I turn up the fan speed"

Anonymous, MO (2012 Ford Fusion SE 2.5-L 4 Cyl)

"The blower motor stopped working. When repaired, it turned out the dealer had to replace an electrical relay. The total cost was over $400, and the same repair had been done a year before"

Anonymous, WI (2012 Ford Fusion SEL 3.0-L V6)

"Replaced under warranty due to worn bearing"

Anonymous, NY (2012 Ford Fusion SE 2.5-L 4 Cyl)

"Fan motor made whining sounds when in operation"

Anonymous, OR (2012 Ford Fusion Hybrid 2.5-L 4 Cyl hybrid)

"Bearing has dried out. Makes suspicious noises"

Genny W., SK (2012 Ford Fusion SEL 3.0-L V6)

"was loud was replaced under warranty"

Shawn K., OH (2012 Ford Fusion SEL 2.5-L 4 Cyl)

"AC blower motor seized up and that caused a electronic mother board to short out. Good thing is that now the part is warranted for longer time"

Anonymous, IA (2012 Ford Fusion SEL 3.0-L V6)
Condenser

"had a hole in it"

Anonymous, GA (2012 Ford Fusion Sport 3.5-L V6)

"Car was not cooling so took to Ford Dealership and was diagnosed refrigerant leak which was covered under warranty"

Robert M., NC (2012 Ford Fusion SEL 3.0-L V6)
Electrical failure

"Climate Control Computer"

Anonymous, GA (2012 Ford Fusion SE 2.5-L 4 Cyl)

"Climate control unit failed"

Lou W., FL (2012 Ford Fusion SE 2.5-L 4 Cyl)

"The electrical control panel was faulty, causing intermittent hot/cold air. The Ford Dealer took 9 days to correct the problem"

Paul G., SC (2012 Ford Fusion Sport 3.5-L V6)
Evaporator

"evidently when the first compressor was replaced the contaminated air that was allowed to enter into the system caused the other compressors to fail since moisture had entered the system during following installations of the other compressors"

Jack H., NE (2012 Ford Fusion SE 3.0-L V6)

"Leak requiring replacement. Happened after air bag recall."

Anonymous, MI (2012 Ford Fusion SEL 2.5-L 4 Cyl)
Heater system

"heats and cools slower than expected"

Jane R., WI (2012 Ford Fusion 2.5-L 4 Cyl)

"The temperature control mechanism failed, and it is buried deep within the dash."

J S., CA (2012 Ford Fusion SE 2.5-L 4 Cyl)
Refrigerant leaks

"Leaking components in AC system"

Anonymous, AZ (2012 Ford Fusion SE 2.5-L 4 Cyl)

"O-ring failure resulted in refrigerant leak. Had purchased extended warranty and was repaired under that warranty"

Anonymous, OH (2012 Ford Fusion S)

"Air conditioning leak"

Rick P., CA (2012 Ford Fusion SEL 2.5-L 4 Cyl)

"Leak was experienced, but it was a very slow one. $500 to fix."

Anonymous, TX (2012 Ford Fusion SE 2.5-L 4 Cyl)

"Air conditioner stopped blowing cold air. Mechanic checked system. Found nothing wrong. Mechanic added very, very small amount of refrigerant. System works now."

Anonymous, MN (2012 Ford Fusion S 2.5-L 4 Cyl)

"No cooling, had to replace a leaking valve."

Anonymous, TX (2012 Ford Fusion SE 2.5-L 4 Cyl)

Suspension

Shocks or struts, ball joints, tie rods, wheel bearings, alignment, steering linkage (includes rack and pinion), power steering (pumps and hoses, leaks), wheel balance, springs or torsion bars, bushings, electronic or air suspension.

What Owners Say

Alignment

"When the shocks and struts were replaed they had to re-align the front end"

Anonymous, WA (2012 Ford Fusion SE 2.5-L 4 Cyl)
Ball joints

"Lower left ball joint began making lots of noise. Could not feel it in steering wheel. First time in 60 years of owning cars that I had to replace a ball joint"

Tom S., TX (2012 Ford Fusion SEL 2.5-L 4 Cyl)

"Ball joint in right front was worn out"

Fritz F., MO (2012 Ford Fusion SEL 3.5-L V6)
Bushings

"L front and L rear suspension arms had unusual wearing and needed replacement at 50,000 miles"

Donald A., CA (2012 Ford Fusion SEL 3.0-L V6)

"Bushing in both control arms went bad. On ac repair, program was bad, had to be reinstall, this was I known issue,, but still had to pay for fords programming error. Was not happy"

Corey A., TX (2012 Ford Fusion SE 3.0-L V6)

"Replacement of all the front end suspension and steering bushings"

Anonymous, VA (2012 Ford Fusion SEL 3.0-L V6)
Electronic or air suspension

"The power steering basically quit working. There had been a recall but our Make and Model was not covered (ie, Ford said the problem had been fixed when it obviously had not). My shop was able to pay for a one day download that appeared to fix the problem. If it comes back it is a $2000 + repair."

Anonymous, (2012 Ford Fusion SE 3.0-L V6)

"no power steering first time under warranty 8months later cost me 1600.00 not a ford fan"

Anonymous, IL (2012 Ford Fusion SEL 2.5-L 4 Cyl)

"I lost steering power which required increased effort to control the vehicle. Problem was with rack mounted electric power assisted steering and fix/replacement was covered under my warrenty"

Anonymous, MD (2012 Ford Fusion SEL 2.5-L 4 Cyl)
Power steering pumps and hoses

"reprogrammed power steering module, replaced power steering gear. This issue is related to the sticking steering at slow speeds It was stated that Ford "may" send out another recall for the control arms and bushings to fix the sticking steering"

Anonymous, VA (2012 Ford Fusion SE 2.5-L 4 Cyl)

"Car no longer uses power steering pump and uses an electronic motor to steer the car instead. Power steering module failed and cost $1700 to fix. Part alone is $1100 and only available from Ford. 8 hours labor because it required taking apart the entire steering column assembly. Dealer would have charged $500 to $700 more. Several Fusions are under recall for this issue but mine was not covered because it was assembled outside of the date range of the recalled vehicles. Many other people affected like me can be found on the internet. Ford needs to own up to this or be subject to a class action lawsuit like it was for a 1997 intake manifold issue it chose to cover for some but not all. Had a 2006 that we regret trading in and my daughter has a 2009 that has been great. Can't believe Ford would ruin such a great car."

James A., FL (2012 Ford Fusion SE 2.5-L 4 Cyl)

"Power steering pump sprung a sudden leak. Just managed to get it to a gas station before steering was gone entirely."

Anonymous, MD (2012 Ford Fusion SEL 2.5-L 4 Cyl)

"Power steering software settings previously had been adjusted under recall. Last summer the entire power steering quit, but I was able to wrestle with it until I could get home. This was covered by an extended recall at no cost to me. The entire steering unit had to be replaced. Most people would have been unable to steer without power assist, but I have strong arms."

Anonymous, DE (2012 Ford Fusion S 2.5-L 4 Cyl)

"Pump went out causing me to drive 150 miles with out power assisted steering. Turned out is was something Ford had issued a recall for, so it was replaced at no cost."

Anonymous, IN (2012 Ford Fusion SEL 3.5-L V6)

"I never knew about the power steering problem until the light went on in my car. Fixed by Ford under warranty."

Anonymous, (2012 Ford Fusion Unsure 2.5-L 4 Cyl)

"power steering failed at 49000 kilometres and was replaced on warrenty"

Anonymous, MB (2012 Ford Fusion SE 2.5-L 4 Cyl)

"HAD TO BE REPLACED AT 45000 MILES FOR $1300"

Anonymous, NE (2012 Ford Fusion SEL 2.5-L 4 Cyl)

"multiple times, the power steering quit working during a turn in traffic"

Louise S., GA (2012 Ford Fusion SE)
Shocks or struts

"Front struts replaced with Monroe quick-struts. Had severe clunking in front end. Ford techs tore the whole front end apart, eventually taking the strut assemblies off a "12 Fusion with similar mileage. Clunking gone. Replaced with OEM struts. Constant rattling no longer present, but now has extremely harsh ride and front end is still very noisy over bumps. They replaced a worn suspension arm on L front and L rear suspension saying they were unusually worn. Now I hear clunking in rear over smal"

Donald A., CA (2012 Ford Fusion SEL 3.0-L V6)

"EXPENSIVE to replace!!"

Christopher T., WA (2012 Ford Fusion SEL 3.0-L V6)

"Rear shocks required replacement at 70K miles. They went out without any notice, and in the span of about two months."

Anonymous, WA (2012 Ford Fusion SE 3.0-L V6)

"Had to replace them at 60k miles and then again at 130k"

Anonymous, NM (2012 Ford Fusion SEL 3.5-L V6)

"I had noticed that the ride had become harsh over bumps. After 152000 plus miles, I though it might be time for new shocks. When I told my mechanic, she said I had struts in the front. I had them replaced. Problem solved."

Anonymous, (2012 Ford Fusion Sport 3.5-L V6)

"Popping noise in front driverside suspension when going over small changes in road grade. Suspect worn struts but have not fixed yet."

Anonymous, (2012 Ford Fusion SE 2.5-L 4 Cyl)

"At 150000 miles they just wore out"

Anonymous, WA (2012 Ford Fusion SE 2.5-L 4 Cyl)

"Front struts needed replaced"

Anonymous, PA (2012 Ford Fusion SEL 2.5-L 4 Cyl)
Springs or torsion bars

"During a routine service, cracks were found on the front springs. The car had to be stopped for safety reasons. After some research, it turns out this is something that has happened before as reported by other Fusion owners. The car was repaired accordingly at the next available opportunity."

Anonymous, OH (2012 Ford Fusion Sport 3.5-L V6)

"Broken spring 6 months old. Replaced under warranty"

Anonymous, ON (2012 Ford Fusion SEL 2.5-L 4 Cyl)
Steering linkage (includes rack and pinion)

"reprogrammed and replaced and still did not fix the problem of sticking steering at slow speeds"

Anonymous, VA (2012 Ford Fusion SE 2.5-L 4 Cyl)

"Sudden and complete loss of power steering because of faulty rack and pinion. Issue was known to Ford and a recall was issued by Transport Canada. Recall covered vehicles built on or before February 28, 2012. Mine was built early in March, 2012 in the same plant using the same rack and pinion. Ford would not cover the repair even though the dealership service facility determined the problem was the same as those built before March. Cost me over $1700.00. I complained directly to Ford Customer Service. Their reply was that we only cover recalls ordered by Transport Canada and mine was not included because of the build date."

John M., NB (2012 Ford Fusion SEL 3.0-L V6)

"There is a recall on the steering gear in the rack and pinion. I took it to Jim Click Ford and they agreed that was causing the popping sound. Ford would not honor their extended warranty under this recall and the matter is being investigated by the NHTSA."

Anonymous, AZ (2012 Ford Fusion S 2.5-L 4 Cyl)

"the steering system would get hard to operate. The electronic power steering system was bad."

Scott M., PA (2012 Ford Fusion SE 2.5-L 4 Cyl)

"This car has electric steering. The main box had to be replaced at a cost of over 1000. I understand that thee is a secret warranty and that this is a known defect."

Anonymous, CA (2012 Ford Fusion SE 2.5-L 4 Cyl)

"At roughly 73K miles, due to a noise that occurred during turning at low speeds, I had to have the upper and lower steering arms replaced on both the driver and passenger sides."

David M., WA (2012 Ford Fusion SE 3.0-L V6)

"This was part of the same repair along with the power steering unit."

Anonymous, DE (2012 Ford Fusion S 2.5-L 4 Cyl)

"The electronic control on the rack & pinion started to make clunking noises when the steering wheel was turned at low speeds. It started in Summer 2019. Ford looked at it and diagnosed the problem and ordered parts. They fixed it in early Fall 2019. They checked and found it was part of a Technical Note (whatever that is) and fixed it for free in 1.5 days. I got a loaner and am very satisfied both with Gaudin Ford and the repairs. No problems since."

Anonymous, (2012 Ford Fusion SE 3.0-L V6)

"The power steering went out and caused an accident"

J S., CA (2012 Ford Fusion SE 2.5-L 4 Cyl)

"Steering wheel started slippng and jerking. Rack and Pinion was replaced under extended warranty"

Anonymous, VA (2012 Ford Fusion Hybrid 2.5-L 4 Cyl hybrid)

"Complete loss of steering. Steering rack had to be replaced at 80000km"

Anonymous, NL (2012 Ford Fusion SE 2.5-L 4 Cyl)
Tie rods

"The tie rods broke out of nowhere"

Anonymous, MI (2012 Ford Fusion SE 2.5-L 4 Cyl)

"I had uneven tire wear, took it in for tire rotation and alignment. Discovered worn tie rod ends. Replaced tie rods and aligned. Problem solved."

Anonymous, GA (2012 Ford Fusion SEL 2.5-L 4 Cyl)
Tire wear is uneven

"Mercury Sable had uneven tire wear due to a spring, not the Honda."

Anonymous, (2012 Ford Fusion Unsure 2.5-L 4 Cyl)

"The left front wore on the inside at twice the rate of the outside and other 3 tires"

J S., CA (2012 Ford Fusion SE 2.5-L 4 Cyl)
Wheel bearings

"Right front wheel bearing failed. The vehicle was able to drive, but the vibration was bad enough that more than a few miles was too annoying, and risked complete failure."

Anonymous, MS (2012 Ford Fusion SEL 3.0-L V6)

"Premature bearing failure on the left rear wheel hub. Car starting making a warbling sound and prematurely worn out the tire. Had to replace hub and bearing plus rotor and break pads on both sides"

David J., NC (2012 Ford Fusion SEL 3.0-L V6)

Transmission Minor

Gear selector or linkage, leaks, transmission computer, transmission sensor or solenoid, clutch adjustment, rough shifting, slipping transmission.

What Owners Say

Coolers and lines

"water pump broke on the interstate, loss of coolant, engine overheating, loss of power, had to pull off the highway and get towed several miles to a Ford dealership, was the weekend so had to stay at a motel 2 nights, Ford dealership in Orangeburg S.C. fixed it well and in a timely manner on a Mon. so was able to continue trip to Charleston S.C."

Anonymous, OH (2012 Ford Fusion 2.5-L 4 Cyl)

"cooler line was observed to be corroded... Replaced prior to it causing any issues"

Anonymous, NY (2012 Ford Fusion SE 2.5-L 4 Cyl)
Rough shifting

"At highway speeds, it's started to roughly up or down shift in occasion"

Anonymous, MO (2012 Ford Fusion SE 2.5-L 4 Cyl)

"When I had the transmission leak fixed, the rough shifting quit occurring"

Terry M., MA (2012 Ford Fusion SE 2.5-L 4 Cyl)

"hesitated in shifting from 2nd to 3rd when cold, the transmission fluid was low, I feel the car was not properly dealer prepped from new. The dealer did not catch the low fluid until i brought it to their attention!! seems ok now"

Anonymous, OH (2012 Ford Fusion SEL 3.5-L V6)

"Occasionally, the transmission will bang harshly when downshifting immediately after exiting the interstate and going to normal slower city driving. The dealer was never able to find the problem, but it hasn't gone away."

Rodolfo L., PR (2012 Ford Fusion Sport 3.5-L V6)

"Transmission has been rough since purchase. Biggest complaint about car. Dealership says it is a problem with this model, but no recall or repairs recommended."

Anonymous, TX (2012 Ford Fusion SE 3.0-L V6)

"The transmission shifts roughly occasionally from 1st to 2nd and accelerating. By slowly evenly speeding up I can avoid the rough shifting in most circumstances. Been doing it since I bought the car with 4400 miles on it. Adjusting and replacing fluid didn't help."

Anonymous, (2012 Ford Fusion SEL 2.5-L 4 Cyl)

"After we owned this car about a year, the dealer drained, flushed and refilled the transmission but shifting behavior was not improved. When the car is started after being parked overnight in the garage, shifting from gear 1 to gear 2 and to gear 3 is erratic and rough while accelerating modestly. Shifts above gear 3 are not perceptible. After driving a mile or two, the shifting behavior becomes more normal. I cannot tell if the problem is related to engine or transmission temperature. After driving several miles, transmission action is so smooth I am not aware of shifting action."

Anonymous, (2012 Ford Fusion SEL 3.0-L V6)

"low speed shifting like a manual trans. dose"

Anonymous, NJ (2012 Ford Fusion SEL 2.5-L 4 Cyl)

"Seemed to be sluggish on take-off, and shifting"

Anonymous, AR (2012 Ford Fusion SEL 2.5-L 4 Cyl)

"The transmission would shift roughly in the 30 to 35 mph range. My car was under warranty and my dealer solved the problem. It required that I leave my car for one day. And I had the use of a free loaner vehicle"

Anonymous, MN (2012 Ford Fusion SEL 2.5-L 4 Cyl)

"Transmission surge. Not totally corrected with software update"

Anonymous, FL (2012 Ford Fusion SEL 3.0-L V6)

"does not shift smoothly"

Anonymous, ON (2012 Ford Fusion SEL 3.5-L V6)

"Shifted rough on occasion- also had a delay in shifting between 2-3"

Anonymous, WI (2012 Ford Fusion SEL 2.5-L 4 Cyl)

"Doesn't know if it wants to shift up or down. Had to the dealership several time to no avail. Googled it and found out that basically it is a poor design. Need to complain to Ford directly if it's not fixed after our next try. they keep putting on p"

Anonymous, FL (2012 Ford Fusion SE 3.5-L V6)
Slipping transmission

"Slipping or jerking when shifting gears"

Anonymous, AR (2012 Ford Fusion SEL 2.5-L 4 Cyl)

"Transmission slips when shifting from first to second gear when vehicle is cold. After driving for a few miles it seems to shift fine"

Anonymous, TX (2012 Ford Fusion SEL 3.5-L V6)

"Transmission slips at low speeds. Warranty has been extended due to this problem, something in the transmission sensor control module in the transmission. There is also a second warranty extension for transmission clutch shudder"

Anonymous, MB (2012 Ford Fusion SE 2.5-L 4 Cyl)

"It seems to slip on occasion from 1-2 and 2-1, usually after driving a bit"

Anonymous, CA (2012 Ford Fusion SE 2.5-L 4 Cyl)
Transmission computer

"The car bucked when accelerating"

Anonymous, NJ (2012 Ford Fusion SE 2.5-L 4 Cyl)

"Shifts at unusual and unpredictable times. Sometimes will not engage at all when braking then immediately stepping on gas pedal gradually. In this case vehicle may require full gas pedal before engine will respond to move forward again"

Anonymous, AZ (2012 Ford Fusion SE 3.0-L V6)

"due to rough shifting the computer has been reprogrammed twice"

Anonymous, ON (2012 Ford Fusion SEL 3.5-L V6)

"Transmission was not responding as quickly as it should. I think they had to reset/readjust the computer"

Anonymous, AZ (2012 Ford Fusion SEL 3.0-L V6)
Transmission leaks

"I bought the car the end of May 2016. Had a transmission leak and the dealer fixed it in June 2016 (was under warranty). In December 2016, car had another transmission leak (warranty expired). I was told by the Ford dealership that the second leak had nothing to do with the first leak. Paid appx. $600 out of pocket to fix. Car drives fine now....no leaks.....no rough shifting"

Terry M., MA (2012 Ford Fusion SE 2.5-L 4 Cyl)

"Had checked and leak from right and left and needed shaft?"

Anonymous, IL (2012 Ford Fusion SEL 2.5-L 4 Cyl)

"small leak since new"

Anonymous, NJ (2012 Ford Fusion SEL 2.5-L 4 Cyl)

"Dealer found bad seals when investigating hal shaft problem"

James R., IL (2012 Ford Fusion SEL 2.5-L 4 Cyl)
Transmission sensor or solenoid

"Warranty extended to 7yrs 160k klms due to the problem. Includes the input shaft seals"

Anonymous, MB (2012 Ford Fusion SE 2.5-L 4 Cyl)

Electric System

Alternator, starter, hybrid battery and related systems, regular battery, battery cables, engine harness, coil, ignition switch, electronic ignition, distributor or rotor failure, spark plugs and wires failure.

What Owners Say

12V power plug

"Outlet loosen up and came out had to reattach outlet."

Anonymous, WI (2012 Ford Fusion SEL 2.5-L 4 Cyl)
Clock

"The numbers are too small to read easily. The highest brightness setting is still too dim. All control backlights (Fan, radio, A/C) are too small to read easily and too dim. The whole ergonomic set-up is unintuitive. Everything in the center dashb"

Anonymous, LA (2012 Ford Fusion SEL 3.0-L V6)
Exterior lights (other than headlights)

"back light bulb and socket separated from wiring. Trying to fix, they slipped into the sealed light fixture and had to replace both pieces."

Jon M., NJ (2012 Ford Fusion SE 2.5-L 4 Cyl)

"Known defect involving grounding issue with tail light bulbs."

Anonymous, SC (2012 Ford Fusion SE 2.5-L 4 Cyl)

"right rear directional signal light bulb failed"

Lee L., MI (2012 Ford Fusion SEL 3.0-L V6)

"Passenger side rear tail light assembly froze up after bulb blew, requiring replacement to allow new bulbs. Warranty service"

Gregory H., VA (2012 Ford Fusion SEL 3.0-L V6)

"Rear brake light went out and we replaced it ourselves for $5"

Anonymous, MI (2012 Ford Fusion SE 3.0-L V6)

"Fuse went out and tail lights didn't work"

Anonymous, TX (2012 Ford Fusion SEL 3.5-L V6)

"Right brake and directional light work intermittently. When the bulb was replaced there was a component broke due to corrosion"

Anonymous, RI (2012 Ford Fusion SEL 2.5-L 4 Cyl)

"the turn signal blinkers bulbs burned out; had to be replaced; the right occurred first and within 4 months the left signal bulb went out"

Agustin A., TX (2012 Ford Fusion SEL 2.5-L 4 Cyl)

"Rear signal light out"

Erika B., CA (2012 Ford Fusion SE 2.5-L 4 Cyl)
Gauges

"Dash went blank intermitely"

Anonymous, CA (2012 Ford Fusion SEL 3.0-L V6)
Headlights

"We had to change a part to fix it. Labor was over $120.00"

Henry D., NE (2012 Ford Fusion SE 2.5-L 4 Cyl)
Heated or cooled seats

"The heated seat pad shorts out and burns the foam in the seat pad. This has happened once since I purchased the car and I had to take the entire seats out to replace it with a new heating element"

Corbin L., CT (2012 Ford Fusion SEL 2.5-L 4 Cyl)

"Heated Seat stopped working. Covered by extended warranty"

Anonymous, MN (2012 Ford Fusion SEL 2.5-L 4 Cyl)

"heated seat on drivers side stopped working at 40000. Cost 300 to fix"

J B., NY (2012 Ford Fusion Sport 3.5-L V6)

"Drivers side heated seat quick working and had to replaced which was under my extended warranty when I purchased my car in 2012."

Bob L., MN (2012 Ford Fusion SEL 3.0-L V6)

"The driver's side heater works intermittently and it appears the heating element for the back rest is no longer working. After some research, it is a fairly common Ford products problem, and one that requires an expensive repair due to its complexity."

Anonymous, OH (2012 Ford Fusion Sport 3.5-L V6)

"The control for movement of power seat fails randomly. Replacement switch on order."

Anonymous, WI (2012 Ford Fusion SEL 2.5-L 4 Cyl)

"The driver's side heated seat control quit working and was replaced under factory warranty"

Anonymous, MN (2012 Ford Fusion SEL 3.0-L V6)

"apparently, heating core burned out in drivers side.' I have extended warranty. Minimal cost to me"

Anonymous, WI (2012 Ford Fusion SEL 2.5-L 4 Cyl)

"Heating element failed"

Anonymous, MO (2012 Ford Fusion SEL 2.5-L 4 Cyl)

"Exposed wiring within heated seats blew the fuse for the seats"

Jason O., AB (2012 Ford Fusion SEL 2.5-L 4 Cyl)
Interior lights

"Dash lights would go dark while driving, then would come back on seconds later. Dealer replaced dash light dimmer switch twice. Did not fix problem. Replaced module. Seems to be ok for now"

Anonymous, VT (2012 Ford Fusion SE 2.5-L 4 Cyl)
Keyless entry

"The keyless entry wouldn't function at all with either key fob. The Ford dealer fixed it for less than $300."

Michael G., UT (2012 Ford Fusion SEL 2.5-L 4 Cyl)
Remote engine starter

"The car refused to start remotely. The dealership had to replace the remote starter control unit."

Rodolfo L., PR (2012 Ford Fusion Sport 3.5-L V6)
Tire pressure monitor

"Has gone off a couple of times with no problem, I believe in winter, was reset once and wentoff again within 2 weeks. Other times o once reset. FYI dealer checked the tires every time free"

Anonymous, MA (2012 Ford Fusion SE 2.5-L 4 Cyl)

"Tire pressure monitor is defective"

Anonymous, RI (2012 Ford Fusion SEL 2.5-L 4 Cyl)
Warning lights

"Air bag light occurs periodically. Rear signal light intermittent"

Anonymous, NY (2012 Ford Fusion Sport 3.5-L V6)

Fuel System

Check engine light, sensors (includes O2 or oxygen sensor), emission control devices (includes EGR), engine computer, engine computer, fuel cap, fuel gauge/sender, fuel injection system, fuel pump, fuel leaks, stalling or hesitation.

What Owners Say

Emission control devices (includes EGR)

"For the cooler part of the year, usually OCT-MAY, I will often get error P0456 emission system leak (very small). From the online research I've done, this is a very common problem with capless fuel system. I have tried all of the remedies suggested online, but error reoccurs usually within 200 miles after clearing the ODB error. The error goes away during the warmer parts of the year. Given the age of the issue, the three primary causes of it most often mentioned online, and the low mileage on the vehicle, I am not happy that Ford hasn't addressed this issue via a recall. One part, the fuel system 'tube' from fueling port to gas tank, costs $350-$400 to replace (not including labor) and that MAY NOT FIX THE PROBLEM. Which would lead to additional expense in replacing the emission fume tank or a emission valve on the engine. I should note that the common fix, which involves cleaning and lubricating the capless fuel port, has been performed several times, and issue has not resolved itself. Also, I should note that I have a locking cap on the capless fuel port, so it's not dust/dirt getting into the inlet part of the fueling part and preventing the capless system to seal. Issue started in 2017, and is not resolved. I may file a claim against my extended 3rd party warranty and have a repair shop deal with it as long as the claim is approved in advanced. But I do not expect emission system components to not work/produce ODB errors when the vehicle is less than 10 years old, and is driven 10,000 miles or less per year."

Anonymous, WA (2012 Ford Fusion SE 3.0-L V6)

"Electronic module in emission system had to be replaced"

Jeffrey H., CA (2012 Ford Fusion SEL 2.5-L 4 Cyl)
Fuel cap

"The fuel cap sensor constantly indicates a leak"

Anonymous, MD (2012 Ford Fusion SEL 2.5-L 4 Cyl)

"Because it has no fuel cap ( never had one a ford better idea) the check engine light comes on often and I have to clean around the flap because dirt gets in their and it doesn't close completely"

Ronald W., MA (2012 Ford Fusion SE 2.5-L 4 Cyl)

"Cap less fuel pipe gives check engine code.I have to have it reset by my mechanic and then drive about 50 miles in order for car to pass inspection."

Brian C., MA (2012 Ford Fusion SE 3.0-L V6)

"Getting a error light on the dash board from a vacuum leak on the fuel line used to put gas into the gas tank. This car does not have a gas cap and the Ford dealership said I would have to replace the entire fuel infeed line that feeds the fuel into the gas tank."

Don C., KS (2012 Ford Fusion SE 3.5-L V6)

"Capless gas fill system causes intermittent P0456 code (small vacuum leak)"

Jerry D., SC (2012 Ford Fusion SE 2.5-L 4 Cyl)

"I was getting a service engine light on because the no cap fuel was not working . We had to have the whole system replaced to get the sensor to work properly as there was some pressure leak that set off the sensors"

Anonymous, WI (2012 Ford Fusion SEL 3.0-L V6)

"The car has a 'capless' fuel tank. Most owners end up having an evap leak issue with this item, but Ford has never issued a fix or recall."

Anonymous, MD (2012 Ford Fusion SEL 2.5-L 4 Cyl)

"Check engine light went on. Dealer first replaced a sensor. The check engine light went on again about a week later. This time the fuel fill neck assembly was replaced. Apparently the problem was in the fuel filler neck (this car does not have a"

Anonymous, PA (2012 Ford Fusion SE 2.5-L 4 Cyl)

"Filler neck leaked preventing annual inspection pass"

Risto B., MA (2012 Ford Fusion SE 2.5-L 4 Cyl)

"Capless fuel filler system has had to be replaced twice"

Jeffrey H., CA (2012 Ford Fusion SEL 2.5-L 4 Cyl)

"Check engine light came on. Code indicated evap. System leak. Problem was found to be self sealing fuel cap. Was replaced under warranty"

William A., GA (2012 Ford Fusion SEL 2.5-L 4 Cyl)
Fuel injection system

"There has even hesitation in accelerating ever since purchase. Mfr and dealer still haven’t fixed it. Must be aFord speciality product never working as designed."

Anonymous, VA (2012 Ford Fusion SEL 3.0-L V6)

"While driving the car slowed down to a stop. When called Ford they explained it was a recall situation with the throttle and had it fixed. So far no more problems."

Anonymous, AZ (2012 Ford Fusion SE 2.5-L 4 Cyl)

"BAD SENSOR OR CONTROLLER, WAS COVERED BY WARRANTY"

K C., CA (2012 Ford Fusion SE 3.0-L V6)

"There was a throttle problem causing the engine to choke out when accelerating"

James L., NY (2012 Ford Fusion SEL 3.0-L V6)
Fuel pump

"Driving down the road and car decelerated to a stop. had to tow it in."

Sidney L., GA (2012 Ford Fusion SE 3.0-L V6)

"Same symptons as a recall on other vehicles, 1200 to repair"

James K., TX (2012 Ford Fusion SEL 3.0-L V6)

"Car stopped running and would would not start. Phoned Ford, had it towed in and they replaced the fuel pump, no charge"

Anonymous, BC (2012 Ford Fusion Sport 3.5-L V6)
Sensors (includes O2 or oxygen sensor)

"Engine warning light came on at about 64500 km, fault traced to a sensor on the fuel tank, estimated cost to repair $500. Problem not fixed to date, mechanic considered it a minor problem not affecting operation, will fix next time work in that area is being done. Consider rear brake replacement at 60K to be very premature as I try to drive using minimum brake application. Also one or more tire pressure sensors failed, not fixed to date"

David G., ON (2012 Ford Fusion SE 2.5-L 4 Cyl)

"Catalytic converters light comes on frequently at random times regardless of gas level"

Anonymous, (2012 Ford Fusion SEL 2.5-L 4 Cyl)

"engine light indicated need to replace. Slightly lower MPG but drove from FL to NC and then got it fixed"

Anonymous, NE (2012 Ford Fusion Unsure 2.5-L 4 Cyl)

"The check engine light came on. I took the car to the Ford dealership. They ran diagnostics and told me that the oxygen sensor was intermittently failing"

Anonymous, CA (2012 Ford Fusion SE 2.5-L 4 Cyl)

"Low tire pressure warning came on. Put in air on all 4 tires but stayed on. Took vehicle in for maintenance service and problem was rectified with no charge"

Anonymous, BC (2012 Ford Fusion Sport 3.5-L V6)

"Fuel tank pressure sensor unserviceable. Expensive part & repair since the fuel tank must be dropped for access. Vehicle just out of warranty by 600k. I haven't replaced yet, hoping for hidden warranty coverage"

Brian H., ON (2012 Ford Fusion SE 2.5-L 4 Cyl)

Exhaust

Muffler, pipes, catalytic converter, exhaust manifold, leaks.

What Owners Say

Exhaust leaks

"To be expected with mileage"

Bruce N., MN (2012 Ford Fusion SEL 2.5-L 4 Cyl)

"Resonator has split and am getting quotes. Looks like I have to get other new parts, too."

Anonymous, (2012 Ford Fusion SEL 2.5-L 4 Cyl)

"Exhaust had a high pitch whistle"

Anonymous, IL (2012 Ford Fusion SEL 2.5-L 4 Cyl)
Other/unsure

"The airbag warning light kept coming on after I have taken it back to three different dealers to be repaired, The last dealer on the third try found the wiring harness was defective that solved the problem no more lights."

Robert E., MO (2012 Ford Fusion SEL 2.5-L 4 Cyl)

"Airbag recalled, but no issues with car. Still not fixed."

William L., NV (2012 Ford Fusion SEL 2.5-L 4 Cyl)

"Affected by weather conditions such as snow and rain. Caused system to not function."

D D., NY (2012 Ford Fusion SEL 3.0-L V6)

"Recall due to serious manufacturing defect. When activated, the airbag's metal housing frequently comes with it. Numerous deaths have occurred with metal going through people's necks and such as one normally experiences in war zones rather than safety devices."

Anonymous, WA (2012 Ford Fusion)

"There is an existing Ford recall because I have the Takata airbag, which may explode during a potential accident, possibly causing an injury. I am still waiting for the Ford dealer to call me back when they have the new airbag(s) Seems to be taking bit to long."

Anonymous, MI (2012 Ford Fusion)

"Airbags recall from Ford. Ford made the repairs."

Anonymous, VA (2012 Ford Fusion)

"Takata airbag recall. Ford asked that we not drive the vehicle until it could be repaired, and offered us a rental vehicle through Enterprise Car Rental to use in its place. Rental vehicle was used for approximately five months and was turned in when Ford airbag was fixed."

Anonymous, FL (2012 Ford Fusion S 2.5-L 4 Cyl)

"Recall"

Anonymous, NJ (2012 Ford Fusion SE 2.5-L 4 Cyl)

"Airbag recall. Waited 6 weeks for the dealer to get in the replacement parts."

Peter A., TN (2012 Ford Fusion SE 2.5-L 4 Cyl)

"Recall for airbag replacement"

Barry C., NJ (2012 Ford Fusion SEL 2.5-L 4 Cyl)

"Factory recall issue"

Bruce N., MN (2012 Ford Fusion SEL 2.5-L 4 Cyl)

"Passenger side air bag light is on"

Anonymous, (2012 Ford Fusion SEL 2.5-L 4 Cyl)

"sync system has not worked properly since purchase. Poor sound quality, phone pairing drops frequently. Dealer has made many attempts to fix it in warranty, but it is now out of warranty so I have given up and am just living with its unreliability"

Anonymous, VA (2012 Ford Fusion SEL 3.0-L V6)

"Just not reliable and works poorly, illogically with voice command. (Wish I could upgrade to the RIM based SYNC 3 system when software available on Ford's 2016, 17 or 18 model year vehicles, car or suv.) Do NOT like bundling to get safety options"

Anonymous, MI (2012 Ford Fusion SEL 3.0-L V6)

"Had trouble keeping phones in sync with the system"

James L., NY (2012 Ford Fusion SEL 3.0-L V6)

"Unable to sync phone"

Anonymous, CA (2012 Ford Fusion SEL 2.5-L 4 Cyl)

"Very poor service, Drops phone calls, loses bluetooth connection, speech recognition is poor, often does not operate correctly in hands-free mode"

Anonymous, TX (2012 Ford Fusion Hybrid 2.5-L 4 Cyl hybrid)

"Voice recognition is poor, cannot select iPod tune to play via SYNC, does not update contact list from smartphone via bluetooth properly, dealer not interested/capable of investigating, Ford website is very awkward and ultimately unhelpful. Basicall"

Jan C., BC (2012 Ford Fusion SEL 2.5-L 4 Cyl)

"I had an issue with the SYNC system since i purchased the car. sometimes the system wouldn't work when the car was started, and often times the ipod would constantly disconnect when the car was turned off for a few minutes and then cranked again. D"

Jason C., GA (2012 Ford Fusion SEL 2.5-L 4 Cyl)

In-car Electronics

CD or DVD players, radio, speakers, GPS, communication system (e.g., OnStar), display screen freezes or goes blank, phone pairing (e.g. Bluetooth), voice control commands, steering wheel controls, portable music device interface (e.g., iPod/MP3 player), backup or other camera/sensors.

What Owners Say

Backup or other camera/sensors

"Backup sensors stopped working."

Jon M., NJ (2012 Ford Fusion SE 2.5-L 4 Cyl)

"Backup camera and cross traffic speaker failed, rendering these options useless. Ford dealer wanted $100 to tell me what was wrong (diagnostic charge). I researched the issue and went to a third party shop to have them make the repair..about $200 for speaker and installation."

Anonymous, NY (2012 Ford Fusion SEL 3.0-L V6)

"Blind spot rear sensor went bad and had to be replaced"

Anonymous, MI (2012 Ford Fusion SEL 2.5-L 4 Cyl)

"I had two backup sensors fail just after my waranty expired. Both fixes required an analysis visit and a repair visit and I live 50 miles from dealership!"

D D., NY (2012 Ford Fusion SEL 3.0-L V6)
CD player

"would not eject cd, unit replaced with extended warranty"

June H., FL (2012 Ford Fusion Hybrid 2.5-L 4 Cyl hybrid)
Phone pairing (e.g., Bluetooth)

"Despite inputting the code displayed to pair my iPhone with the Bluetooth device in my Fusion, repeated attemps fail"

Chauncey B., MO (2012 Ford Fusion SE 3.0-L V6)

"The system switches off before I can put in the necessary code."

Anonymous, TX (2012 Ford Fusion Sport 3.5-L V6)

"lost the ability to pair my phone via Bluetooth. This is an issue whenever I'm driving while in possession of my cell phone...can't answer or make calls."

Anonymous, NY (2012 Ford Fusion SEL 3.0-L V6)

"Unable to sync my smartphone to radio"

D L., NY (2012 Ford Fusion SEL 2.5-L 4 Cyl)

"We lost the phone pairing twice and it was difficult to reinstate it"

Alan M., MO (2012 Ford Fusion SE 2.5-L 4 Cyl)

"the reason I purchased this car was because of the [phone. I kept going to the Ford place and the phone co. where my phone was purchased. They would sync the phone and then forget and left it and my radio would not work. Many trips were made to T-M"

Anonymous, CA (2012 Ford Fusion SE)

"Pairing was intermitent on my motorola razor , but when I bought an iPhone the problem stopped"

D D., NY (2012 Ford Fusion SEL 3.0-L V6)

"Unable to connect Phone. Phone was connected but am currently unable to connect even when I try to connect manually"

Anonymous, CA (2012 Ford Fusion SEL 2.5-L 4 Cyl)
Radio

"FM reception is fair. AM reception is not good. Static on most stations, even in the town the station is located in. The dealer replaced a module without much improvement. I tried an after market antenna and it helped some. The radio in our 2010 F150 is great"

Lloyd D., TX (2012 Ford Fusion SEL 2.5-L 4 Cyl)

"Any radio station sound will intermittently muffle as if the speakers were covered. The CD, Bluetooth and Sirius all sound perfect. A technician indicated the problem is a bad antanae or turner."

Brad D., NE (2012 Ford Fusion SEL 2.5-L 4 Cyl)

"radio changes band (am to fm) sometimes when going over a bump"

T C., WA (2012 Ford Fusion SE 3.0-L V6)
Speakers

"THE SPEAKERS COULD BE OF BETTER QUALITY. IF VOLUME IS UP THEY DISTORT. THEY SHOULD BE OF MORE REASONABLE QUALITY"

Lyndel M., AZ (2012 Ford Fusion SE 2.5-L 4 Cyl)
Voice control commands

"Had one software upgrade ($50), in 2014. Microsoft system responds illogically or not at all, 60-70% of the time; experienced the same poor performance after 'upgrade'. Use an Apple 4S smartphone connected via Bluetooth. (Like the big control knobs!)"

Anonymous, MI (2012 Ford Fusion SEL 3.0-L V6)

"IS NOT UNDERSTANDING MY COMMANDS AT TIMES WHEN IT SHOULD, AND THEN IT SPEAKS UNNECESSARY. TOO MANY SUGGESTIONS WHEN IVE GIVEN THE CORRECT INFO., WHICH IS UNNECESSARY AN VERY DISPLEASING"

Lyndel M., AZ (2012 Ford Fusion SE 2.5-L 4 Cyl)

"I have problems with my throat (damaged vocal chords_ and often the voice control does not recognize me. this is probably not due to the car, but me"

Anonymous, CA (2012 Ford Fusion SE)

"Works poorly or not at all. Speech recognition is horrible and many times if fails to connect although bluetooth is functioning"

Anonymous, TX (2012 Ford Fusion Hybrid 2.5-L 4 Cyl hybrid)

Body Hardware

Power or manual windows, locks and latches, tailgate, hatch or trunk, doors or sliding doors, mirrors, seat controls, safety belts, sunroof, convertible top.

What Owners Say

Doors or sliding doors

"Driver door inside handle became inoperable and I was unable to open door from inside. Dealer repair cost over 115 dollars. Apparently, the cord that connects the lever to the unlocking mechanism snapped"

Anonymous, SC (2012 Ford Fusion SE 2.5-L 4 Cyl)

"driver door lock"

Anonymous, AZ (2012 Ford Fusion S 2.5-L 4 Cyl)

"Inner door handle broke on the driver door not long after we bought the car. Cheaply made plastic type part"

Herbert M., MA (2012 Ford Fusion SE 2.5-L 4 Cyl)

"Left front interior door handle failed to cause door to open. Had to roll down window and use outside handle to open door. Researched and found a known problem area, but not a recall. Ordered replacement part online and replaced successfully in a 1/2 hour"

Phoebe W., VA (2012 Ford Fusion SEL)

"The driver side door handle could not open the door from the inside."

Anonymous, NY (2012 Ford Fusion SEL 3.0-L V6)

"door handle component inside door broke. Known problem. Cost $250.00 to fix. Not covered by Ford ESP warranty."

Dean S., VA (2012 Ford Fusion SE 2.5-L 4 Cyl)

"The inside driver's side door handle had to be replaced. Could still open it, but with some difficulty so had in replaced."

Anonymous, MO (2012 Ford Fusion SE 2.5-L 4 Cyl)

"inside door handles (both sides, front) broke, creating inability of fob to operate doors, thus unable to lock/unlock doors using fob"

Anonymous, KY (2012 Ford Fusion SE 2.5-L 4 Cyl)
Heated or cooled seat controls

"Had to have the air control system electrical system worked on because heater did not work"

Annette M., NM (2012 Ford Fusion SEL 3.5-L V6)
Locks and latches

"Passenger door latch sticks"

Phil L., CA (2012 Ford Fusion SE 2.5-L 4 Cyl)

"Driver side door latch failure. My model is not under recall so I replaced it myself. Many other similar models have been recalled for this issue"

Corey H., CA (2012 Ford Fusion SEL 3.0-L V6)

"Drivers door latch broke, leaving me unable to get out of the car without lowering the window and opening it from the outside. An online search shows this to be a very common problem with this car"

John V., PA (2012 Ford Fusion SE 2.5-L 4 Cyl)

"Door handle broke. Interior latch mechanism replaced."

Anonymous, SC (2012 Ford Fusion SE 2.5-L 4 Cyl)

"Door handle broke, preventing the opening of the driver side door. If you do a search this is not a uncommon occurrence, should be a safety recall."

Corey A., TX (2012 Ford Fusion SE 3.0-L V6)

"Door won't open unless you use the lock"

Anonymous, (2012 Ford Fusion Hybrid 2.5-L 4 Cyl hybrid)

"The driver's side door lock latch sticks and it is hard to open from the inside"

Anonymous, PA (2012 Ford Fusion SE)
Mirrors

"driver side heated mirror.....The clips broke and the mirror would not stay in the housing. This in itself was not too big a deal ($100-$200), but I have had several random failures that I don't expect to have : (car door operator, fuel injector, gas cap cover)"

Anonymous, NY (2012 Ford Fusion SEL 3.0-L V6)
Seat belts

"buckle retainer button came off"

Anonymous, MN (2012 Ford Fusion SE 2.5-L 4 Cyl)
Seat controls - movement

"This involved an 8-way powered seat wherein the switch to move the seat forward eventually failed and the entire module had to be replaced. This was a five minute job done by my son-in-law who is a Ford mechanic."

Kathy S., DE (2012 Ford Fusion S 2.5-L 4 Cyl)
Tailgate, hatch or trunk

"We have seen other Ford Fusions with the same problem in the same spot. Paint and primer peels exposing bare metal"

Ray V., ON (2012 Ford Fusion Sport 3.5-L V6)
Windows

"Window regulator went bad. Cheaply made"

Herbert M., MA (2012 Ford Fusion SE 2.5-L 4 Cyl)

Body Integrity

Squeaks, rattles, wind noises, loose or cracked seals and/or weather-stripping, air and water leaks.

What Owners Say

Air or water leaks

"replace water pump"

Anonymous, CT (2012 Ford Fusion SE 2.5-L 4 Cyl)

"Leak from sun roof"

Anonymous, IL (2012 Ford Fusion SE 2.5-L 4 Cyl)

"Wateer pump failed"

Anonymous, AZ (2012 Ford Fusion SE 2.5-L 4 Cyl)
Seals and/or weather-stripping

"Very bad hum at high speed on passenger front door"

David T., NC (2012 Ford Fusion SEL 2.5-L 4 C